How to Apply Polyurethane Sealant in the automotive industry？
HY466 polyurethane sealant has high modulus, anti-pollution after curing, and is environmentally friendly.
It is suitable for bonding and sealing the joints of various materials such as car bodies, train high-speed rail cars, elevator cars, containers, ships, mechanical ventilation equipment, architectural decorations, etc.
This product meets environmental protection requirements, does not contain harmful substances in GB18583 "Limits of Hazardous Substances in Adhesives for Interior Decoration Materials", meets the EU ROHS and REACH environmental protection standards, and meets the German environmental protection standards for automotive adhesives.
What's the advantages of HY466?
· One component,easy to use, non-sagging , primer free
· Does not shrink or crack stays permanently flexible
· Seals against water, air, gas and dust.
· Solvent-free, odorless, non-polluting, neutral and environmentally friendly.
· Paintable,no bubble,excellent thixotropy and extrudability,
· Suitable for a wide temperature range.
· For most metals such as aluminum, painted steel and glass,
· Excellent weather resistance, aging resistance,
· Excellent tensile and compression recovery
What's the Application Polyurethane Sealant in the automotive industry？
1.used for sealing car/vehicle/bus/truck windshield&side glass
2.car body weld seam sealant
3.Auto roof sealant
How to use of HY466?
1. The surface of the joint should be free of oil stains, dust, impurities, etc.;
2. Cut the glue nozzle into the required size and shape according to the process requirements;
3. Cut off the sealant seal, install the glue nozzle, and put it into the glue gun;
4. Apply the sealant evenly on the joints, the thinnest part is greater than 1mm; when using the pneumatic gun, the air pressure is controlled at 0.3~0.5Mpa;
5. The product can be colored by traditional methods after surface drying, including epoxy resin and acrylic paint.
Matters Needing Attention
1. Avoid construction under 5℃ and humidity less than 20%
2. Pneumatic pressure is strictly prohibited to exceed 0.5 Mpa, if it exceeds 0.5 Mpa, gas will enter the hard packaging tube, and colloidal bubbles will occur.
3. Because the coating contains high solvent content, the glue surface will become soft. In order to obtain the best appearance and performance, the glue should be colored after curing for 24 hours.
4. For special chemical reactions, please contact our technical department
It is suitable for bonding and sealing the joints of various materials such as car bodies, train high-speed rail cars, elevator cars, containers, ships, mechanical ventilation equipment, architectural decorations, etc.
This product meets environmental protection requirements, does not contain harmful substances in GB18583 "Limits of Hazardous Substances in Adhesives for Interior Decoration Materials", meets the EU ROHS and REACH environmental protection standards, and meets the German environmental protection standards for automotive adhesives.
What's the advantages of HY466?
· One component,easy to use, non-sagging , primer free
· Does not shrink or crack stays permanently flexible
· Seals against water, air, gas and dust.
· Solvent-free, odorless, non-polluting, neutral and environmentally friendly.
· Paintable,no bubble,excellent thixotropy and extrudability,
· Suitable for a wide temperature range.
· For most metals such as aluminum, painted steel and glass,
· Excellent weather resistance, aging resistance,
· Excellent tensile and compression recovery
What's the Application Polyurethane Sealant in the automotive industry？
1.used for sealing car/vehicle/bus/truck windshield&side glass
2.car body weld seam sealant
3.Auto roof sealant
How to use of HY466?
1. The surface of the joint should be free of oil stains, dust, impurities, etc.;
2. Cut the glue nozzle into the required size and shape according to the process requirements;
3. Cut off the sealant seal, install the glue nozzle, and put it into the glue gun;
4. Apply the sealant evenly on the joints, the thinnest part is greater than 1mm; when using the pneumatic gun, the air pressure is controlled at 0.3~0.5Mpa;
5. The product can be colored by traditional methods after surface drying, including epoxy resin and acrylic paint.
Matters Needing Attention
1. Avoid construction under 5℃ and humidity less than 20%
2. Pneumatic pressure is strictly prohibited to exceed 0.5 Mpa, if it exceeds 0.5 Mpa, gas will enter the hard packaging tube, and colloidal bubbles will occur.
3. Because the coating contains high solvent content, the glue surface will become soft. In order to obtain the best appearance and performance, the glue should be colored after curing for 24 hours.
4. For special chemical reactions, please contact our technical department
Helen:+8615093235871